Motion - Web Changes

50 recent changes in Motion Web retrieved at 03:21 (GMT)

ConfigOptionPostCapture
The purpose of this is mainly to create smooth video clips each time motion is detected. Use it to you personal taste (and disk space).. This option is the prefer...
ConfigOptionSmartMaskSpeed
Smartmask is a dynamic, self learning mask. Smartmask will disable sensitivity in areas with frequent motion (like trees in the wind). Sensitivity is turned on ag...
ConfigOptionHue
Normally only relevant for NTSC cameras.
ConfigOptionIpv6Enabled
This sets the TCP/IP port number to be used for control of motion using http (browser). Port numbers below 1024 normally requires that you have root privileges. P...
ConfigOptionMinimumMotionFrames
Note that the picture frames are buffered by Motion and once motion is detected also the first frames containing motion are saved so you will not miss anything. T...
ConfigOptionMovieFilename
File extension .mpg or .avi is automatically added so do not include this. This option uses conversion specifiers which are codes that start by % and then a lette...
ConfigOptionLocateMotionStyle
* Set to 'box' will draw the traditional box. * Set to 'redbox' will draw a red box. * Set to 'cross' will draw a little cross to mark center. * Set to '...
ConfigOptionLogLevel
You can use this parameter to set how much information you want from the logging. You will typically use a high value when you are trouble shooting a problem. The...
ConfigOptionStreamMotion
Use this option to save bandwidth when there is not anything important to see from the camera anyway.
ConfigOptionTrackType
Motion has special tracking options which use either a serial stepper motor controller, an iomojo smile cam or a Philips WebCam driver compatible pan/tilt camera ...
ConfigOptionInput
This parameter is really used only with video capture cards that has more than one input. However if you set the input number to e.g. 1 for a USB camera motion wr...
ConfigOptionNetcamKeepalive
* off: The historical implementation using HTTP/1.0, closing the socket after each http request. * on: Use HTTP/1.1 requests that support keep alive as default...
ConfigOptionNoiseTune
This feature makes Motion continuously adjust the noise threshold for distinguishing between noise and motion. The 'noise_level' setting is ignored when activatin...
ConfigOptionStreamPort
Note that each camera thread must have its own unique port number and it must also be different from the webcontrol_port number. A good value to select is 8081 fo...
ConfigOptionThread
This is used when you have more than one camera/device. The single camera can get all its options from the default motion.conf file. If you have two or more camer...
ConfigOptionTrackMotorx
Only used for stepper motor tracking.
ConfigOptionTunerdevice
Make sure to remove or comment out this option when running Motion under Linux.
ConfigOptionAreaDetect
Areas are numbered like that: 1 2 3 4 5 6 7 8 9 One or more areas can be specified with this option. Example: You want to mon...
ConfigOptionDaemon
Daemon mode is what you typically will use once you are done experimenting and have motion run permanently in the background on a server. Wonder about the word an...
ConfigOptionOnEventEnd
Full path name of the program/script. This can be any type of program or script. Remember to set the execution bit in the ACL and if it is a script type program s...
ConfigOptionOnPictureSave
Full path name of the program/script. This can be any type of program or script. Remember to set the execution bit in the file access control list (chmod) and if ...
ConfigOptionTrackStepAngleY
Requires a tracking camera type pwc
ConfigOptionWebcontrolAuthentication
By setting this to on, the control using http (browser) can only be accessed using login and password ( following the Basic Authentication defined in HTTP RFC )
ConfigOptionFfmpegTimelapse
This feature uses ffmpegs libavcodec to encode a timelapse movie saving a picture frame at the interval in seconds set by this parameter. Setting this option to 0...
ConfigOptionQuiet
Only works in non daemon mode.
ConfigOptionRotate
The rotation feature is used when the camera is hanging upside down (180 degrees) or if you choose a picture format in portrait instead of the normal landscape (9...
ConfigOptionSnapshotInterval
The snapshots are stored in the target directory the directory/filename specified by the snapshot_filename option. This is the traditional web camera feature wh...
ConfigOptionTrackSpeed
Only used for stepper motor tracking.
ConfigOptionWebcontrolPort
This sets the TCP/IP port number to be used for control of motion using http (browser). Port numbers below 1024 normally requires that you have root privileges. P...
ConfigOptionFfmpegBps
To use this feature you need to install the FFmpeg Streaming Multimedia System. Experiment to get the desired quality. The better quality the bigger files. This o...
ConfigOptionFfmpegOutputDebugMovies
Works like ffmpeg_output_movies but outputs motion pixel type pictures instead. This feature generates the special motion type movie where you only see the pixels...
ConfigOptionSetupMode
When this option is turned on, Motion starts in setup mode so that the parameters can be set more easily. You can run setup mode in either console mode or daemon ...
ConfigOptionSqlLogTimelapse
Configuration option common to MySQL and PostgreSQL. Motion must be built with MySQL or PostgreSQL support to use this feature.
ConfigOptionV4L2Palette
Supported values are Value Name Short 0 V4L2_PIX_FMT_SN9C10X S910 1 V4L2_PIX_FMT_SBGGR16 BYR2 2 V4L2_PIX_FMT_SBGGR8 BA81 ...
ConfigOptionMaxMpegTime
The parameter sets the limit of the time and not the size of the file
ConfigOptionForm
Form Topic for motion.conf options Name:* *Type: Size: Values: Tooltip message: Option text 50 Option Name always lower case and with under...
ConfigOptionWebcamQuality
The mjpeg stream consists of a header followed by jpeg frames separated by content length and boundary string. The quality level defines the size of the individua...
ConfigOptionWebcamMotion
Use this option to save bandwidth when there is not anything important to see from the camera anyway. Note that this feature was greatly improved from Motion vers...
ConfigOptionWebcamMaxrate
Don't set 'webcam_maxrate' too high unless you only use it on the localhost or on an internal LAN.
ConfigOptionWebcamLocalhost
By setting this to on, the webcam can only be accessed on the same machine on which Motion is running.
ConfigOptionWebcamLimit
Number can be defined by multiplying actual webcam rate by desired number of seconds. Actual webcam rate is the smallest of the numbers framerate and webcam_maxra...
ConfigOptionWebcamPort
Note that each camera thread must have its own unique port number and it must also be different from the control_port number. A good value to select is 8081 for c...
ConfigOptionSqlLogMpeg
Configuration option common to MySQL and PostgreSQL. Motion must be built with MySQL or PostgreSQL support to use this feature.
ConfigOptionSqlLogImage
Configuration option common to MySQL and PostgreSQL. Motion must be built with MySQL or PostgreSQL support to use this feature.
Number of topics: 50
< Previous Page 4 of 41 Next >

See also: rss-small RSS feed, recent changes with 50, 100, 200, 500, 1000 topics, all changes
Topic revision: r2 - 27 Oct 2010, KennethLavrsen
Copyright © 1999-2024 by the contributing authors. All material on this collaboration platform is the property of the contributing authors.
Please do not email Kenneth for support questions (read why). Use the Support Requests page or join the Mailing List.
This website only use harmless session cookies. See Cookie Policy for details. By using this website you accept the use of these cookies.